{
  "translate": {

    "file": "文件",
    "new": "新建",
    "open": "打开",
    "saveas": "另存为",
    "export motion set": "导出动作组",
    "import motion set": "导入动作集",
    "export c": "导出(.c)",

    "edit": "编辑",
    "motion group editor": "动作表编辑",
    "language": "语言",

    "basic motion": "基本动作",
    "custom motion": "自定义动作",
    "sort by creation time": " 按创建时间排序",
    "sort by name": " 按名称排序",
    "deleteconfirmMsg": "确认删除该动作？",

    "save_as_new_motion": "保存为新动作",
    "save": "保存",
    "addmotion": "添加",
    "modify": "修改",
    "delete": "删除",
    "copy": "复制",
    "insert": "插入动作",
    "motionreset": "动作复位",
    "alloutage": "全部失电",
    "undo": "撤销",
    "redo": "重做",
    "connect_disconnect": "连接/断开",
    "calibration": "校准",
    "motionName": "动作组名称",
    "already exists": "动作组已存在",

    "play": "播放",
    "stop": "停止",
    "changespeed": "变速",

    "magnification": "  倍率  ",
    "slow": "慢",
    "normal": "正常",
    "fast": "快",

    "spacecopy": " 复制",
    "spacedelete": " 删除",
    "spacemodify": " 修改",
    "speed": " 应用变速",
    "pastebefore": " 粘贴到此帧前",
    "pasteafter": " 粘贴到此帧后",
    "addbefore": " 添加到此帧前",
    "addafter": " 添加到此帧后",

    "all": "全选",
    "inverse": "反选",
    "none": "不选",
    "apply": "应用",
    "cancel": "取消",

    "id": "ID",
    "name": "名称",
    "Default angle": "默认角度",
    "Deviation": "偏差值",
    "Correction angle": "修正角度",
    "Minimum correction angle": "最小校正角",
    "Maximum correction angle": "最大校正角",
    "reset": "重置",
    "outageall": "全部失电",
    "resetall": "全部重置",
    "Load from file": "从文件载入",
    "Load from RCU": "从主控载入",
    "Save as file": "另存为文件",
    "Write to RCU": "写入到主控",
    "confirm": "确认",
    "calibrationMsg": "是否将偏差信息写入主控，以便下次调用？",

    "saveDialog": "动作已修改但尚未保存，是否保存？",

    "Motorlist": "马达表",
    "Motor 1": "马达1",
    "Motor 2": "马达2",
    "Motor 3": "马达3",
    "Motor 4": "马达4",
    "Motor 5": "马达5",
    "Motor 6": "马达6",
    "Motor 7": "马达7",
    "Motor 8": "马达8",
    "Motor 9": "马达9",
    "Motor 10": "马达10",
    "Motor 11": "马达11",
    "Motor 12": "马达12",
    "Motor 13": "马达13",
    "Motor 14": "马达14",
    "Motor 15": "马达15",
    "Motor 16": "马达16",
    "Motor 17": "马达17",
    "Motor 18": "马达18",
    "Motor 19": "马达19",
    "Motor 20": "马达20",
    "Motor 21": "马达21",
    "Motor 22": "马达22",

    "build": "组装",

    "run": "运行:",
    "wait": "等待:",

    "showMsgErrFile": "请导入匹配的机器人文件！",

    "connected": "已连接",
    "disconnected": "已断开",

    "Backward": "后退",
    "Forward": "前进",
    "Move to right": "右移",
    "Turn right": "右转",
    "Move to left": "左移",
    "Turn left": "左转",
    "Dance 1": "舞蹈动作1",
    "Dance 2": "舞蹈动作2",
    "Dance 3": "舞蹈动作3",
    "Dance 4": "舞蹈动作4",
    "Preparation": "预备动作",

    "First": "第一步",
    "Previous": "上一步",
    "Replay": "重播当前步骤",
    "Next": "下一步",
    "Last": "最后一步",
    "Close": "返回",


    "1579072061064": "如果遇到卡扣与卡槽难以组装，可以用搓子先打磨卡扣的厚度后再尝试组装。",
    "1579072560478": "注意伺服电机方向",
    "1579072983843": "注意S4连接线位置",
    "1579073133245": "注意伺服电机方向",
    "1579073162042": "注意S9连接线位置",
    "1579073205162": "注意伺服电机方向",
    "1579073244868": "注意S3连接线位置",
    "1579073268990": "注意S8连接线位置",
    "1579073384419": "注意S4、S9连接线位置",
    "1579073412741": "注意伺服电机方向",
    "1579073434053": "注意伺服电机方向",
    "1579073460234": "连接插头",
    "1579073530943": "注意UART连接线位置",
    "1579073647806": "注意S3、S4、S5、S8、S9连接线位置",
    "1579073718529": "注意伺服电机方向",
    "1579073764441": "注意S1连接线位置",
    "1579073793872": "注意伺服电机方向",
    "1579073853372": "注意S6连接线位置",
    "1579073916511": "注意伺服电机方向",
    "1579074160040": "注意AD1位置",
    "1579074327674": "连接S1-S10，AD1，UART"

  }
}